Skip to main content Skip to search Skip to main navigation
Go to homepage

Yamaha R6 Racing Alternator Kit 03-05

Yamaha R6 Racing Alternator Kit 03-05 – without comfort relay is the version of the BDK Racing alternator kit for the YAMAHA YZF-R6 / R6 599 (2003–2005): lightweight rotor for reduced gyroscopic forces on the crankshaft and faster downshifting, without comfort relay (electrical consumers are disconnected) – for track use and racing conversions.

  • TypeBDK RacingRacing alternator kit, ready to fit
  • Scope of deliveryCom­plete kitRotor, stator, regulator/rectifier
  • Model years2003–2005Yamaha
FitsYAMAHA YZF-R6 / R6 599 2003–2005
Part numbersRG-YAM-R6-03-05.2

Ready-to-fit racing alternator kit from BDK Race Engineering for the Yamaha R6 (2003–2005): lightweight magnet rotor, stator with mounting plate and a dedicated regulator/rectifier, pre-assembled with all connectors. Significantly lighter than the standard system and more powerful than typical race kits – for sharper throttle response, reduced gyroscopic forces and more power across the whole rev range.

  • Rotor diameter45 mmStandard approx. 120 mm
  • Rotor weight198 g78% lighter
  • Peripheral speed120 km/hat 14,000 rpm, standard approx. 320 km/h
  • Power gainapprox. 4–5 hpdepending on engine

1What you will feel on track

  • Quicker direction changesLess rotating mass on the crankshaft means reduced gyroscopic forces – the bike is easier to flick over, especially through chicanes and S-bends.
  • Stability under brakingEngine speed matches much faster when downshifting: quicker downshifts, a calmer rear end, more time on turn-in and later braking points.
  • More direct throttle responseThe engine revs more freely and responds more immediately to the throttle – noticeable when accelerating out of corners.

2Why the small rotor makes such a difference

What matters is not only the weight of the rotor, but also where that weight sits. The BDK rotor weighs just 198 g, 78% less than the standard rotor at 890 g, and has a diameter of only 45 mm instead of around 120 mm. At 14,000 rpm, a standard rotor reaches a peripheral speed of around 320 km/h, while the BDK rotor reaches only around 120 km/h. A considerably smaller mass that also moves much more slowly can be accelerated and slowed down far more quickly – and you will feel exactly that in throttle response, acceleration and downshifting.

FeatureStandard alternatorBDK kit
Rotor diameterStandard alternatorapprox. 120 mmBDK kit45 mm
Rotor weightStandard alternator890 gBDK kit198 g
Peripheral speed at 14,000 rpmStandard alternatorapprox. 320 km/hBDK kitapprox. 120 km/h
Regulator/rectifierStandard alternatorStandard regulator, converts excess power into heatBDK kitBDK regulator/rectifier with cut-off logic

3More than a typical race kit

On fuel-injected bikes, a total-loss system without an alternator is not an option because of the fuel pump and injectors. The standard alternator, however, is designed for lighting and road use and delivers far more than a race bike needs – this is where weight can be saved on the crankshaft.

  • Typical race kitsSmall rotor, few windings and the standard regulator/rectifier: usable output is only available at high revs, and excess current is converted into heat in the regulator/rectifier.
  • BDK windingMany turns of fine wire deliver strong, consistent charging output even at medium revs.
  • BDK regulator/rectifier with cut-off logicOnce the target voltage is reached, the regulator/rectifier disconnects generation. The crankshaft is not loaded unnecessarily and the regulator/rectifier stays considerably cooler.

4Technical details

  • Three-phase alternator with nine poles and six internal permanent magnets, designed for 4,000 to 17,000 rpm.
  • Stator lamination stack made of iron-cobalt alloy (49Fe-49Co-2V) instead of silicon steel: around 30% higher flux density, 0.15 mm lamination thickness, iron losses reduced by a further 60%.
  • High-coercivity magnets and a high-strength steel retaining band to withstand centrifugal forces up to 18,000 rpm.
  • Winding made of scratch-resistant inverter wire to cope with the fast voltage spikes at up to 580 Hz.

5Scope of delivery and versions

  • Lightweight rotor (45 mm, 198 g)
  • Stator with mounting plate and housing, fixing material
  • BDK regulator/rectifier with cut-off logic
  • Pre-assembled cables and connectors
Comfort relay (optional, +69 EUR)switches the regulator's power supply with the ignition, so you don't need to disconnect anything after riding

6Battery and accessories

A racing alternator only starts charging at approx. 4,500 rpm and deliberately delivers less charging output than the standard system. The battery therefore needs reserves:

7Important installation notice

for racing alternator kits from BDK Race Engineering

A BDK racing alternator kit replaces your motorcycle's rotor, stator and regulator/rectifier with a significantly lighter unit designed for racing use. This provides a noticeable reduction in rotating mass – but requires careful installation and involves changed operating behaviour. To ensure your kit works reliably from the outset, here is an overview of the most important points.

Who should carry out the installation?

Installation should be carried out by an experienced mechanic – someone who is confident working on the engine and the vehicle's electrical system. Specifically, this includes:

  • Removal of the alternator cover, flywheel/rotor, starter clutch and stator, including securing the Woodruff key (rotor key)
  • Removal and refitting of the ignition pulse sensor (pickup), maintaining the original installation position
  • Working with thread locker and specified torque values according to the manufacturer's instructions
  • Cleaning sealing surfaces, correctly fitting new gaskets and locating dowels, and sealing the cable grommet
  • Professional crimping of the spade connectors and fitting of the connector housing
  • Connection and fusing of the regulator/rectifier in the vehicle electrical system, plus measurements with a multimeter in AC and DC

What matters during installation

  • Thread locker is mandatoryAll screws must be fitted with thread locker and tightened to the specified torque. Failures have already occurred due to missing thread locker – this is the most common avoidable mistake.
  • Only use the supplied regulatorThe standard regulator must never be used with a racing alternator. The regulator body must have a permanently clean earth connection.
  • Regulator mountingOn a flat metal surface exposed to airflow, away from exhaust heat. One mounting point bolted, the second secured with a cable tie.
  • Pay attention to cable managementRoute the stator and pickup wires and secure them with the original clamps as done from the factory – free of chafing, with sufficient movement clearance, and not pinched. A chafed cable causes a short to earth.
  • ConnectorsEvery spade connector must click audibly into place. The order of the three stator wires is not important – a secure fit is what counts.
  • Fusing and switched positiveAn intact fuse (30 or 35 A depending on kit) must be fitted in the positive line. The signal wire must be connected to a switched 12V positive supply so that no standing current flows when parked.
  • Follow the original installation instructionsSequence, torque values, gasket part numbers and cable lengths are model-specific and are detailed in the enclosed BDK instructions.

What changes during operation

A racing alternator deliberately delivers less charging output than the standard system. Depending on the kit, it only starts charging from around 3,000 to 5,000 rpm; prolonged running at lower engine speeds will discharge the battery. This results in three fixed rules:

  1. Always start with a fully charged battery, using at least a 7.8 Ah LiFePO4 battery, ideally 10.4 Ah.
  2. After each session, remove the fuse at the regulator, disconnect the 12V supply, or use a battery disconnect switch – otherwise deep discharge may occur.
  3. Never start or run the bike with the battery disconnected or the regulator unplugged. This will damage the alternator.

Diagnostics

The installer should be able to independently check with a multimeter: the fuse and switched positive supply, continuity between the stator pins (present between each other, none to earth), the AC voltage between the stator pins at a constant engine speed, and the charging voltage at the battery. This allows almost all faults to be narrowed down within a few minutes – often to something minor such as a blown fuse or a connector that hasn't clicked into place. The specific target values can be found in the troubleshooting section of the enclosed instructions.

Properties

Compatibility

BrandModelYears
YamahaYAMAHA YZF-R6 / R6 5992003–2005

Installation Intro

Preview of the installation manual: introduction, safety rules and scope of delivery.

RacePace Performance
BDK Race Engineering Manufacturer: B.D.K. Race Engineering, Norwich (UK)

Fitting Instructions
BDK Race Generator Kit

Yamaha YZF-R6 · model years 2003–2005 (RJ05/RJ09, fuel injection) · kit with complete generator cover

These instructions take you step by step through removal, fitting, electrical connection, commissioning and testing of the kit. On the R6 kit the stator windings assembly comes ready fitted in the complete generator cover with stator connector – there are no mounting plates and nothing to crimp. Mechanically only the flywheel is exchanged: the BDK rotor is bolted to the starter clutch in place of the original flywheel, using the supplied aluminium washer. They supplement BDK's short English guide with test values, a sign-off checklist and practical experience. Please read in full before you start.

ItemRG-YAM-R6-2003-05 (BDK Racing Lima)
DocumentEA-YAM-R6-03-EN
Revision2026-09 (replaces previous versions)
LanguageEnglish
Time requiredapprox. 2–3 h (experienced)
Difficulty●●●●● demanding
The five rules that decide between success and damage
  1. Fit all screws with thread-locking compound and tighten to the specified torque. Failures have occurred without thread-lock – this is the most common avoidable mistake.
  2. Rotor bolt ≈ 34 Nm, maximum 35 Nm with thread-lock and the supplied aluminium washer under the original washer – never the OEM value for the Yamaha flywheel.
  3. Use only the supplied racing regulator/rectifier. The original regulator destroys the race generator. The regulator housing must be properly earthed.
  4. Blue sense wire to switched positive 12V supply (ignition live). Permanent live drains the battery when parked, missing live prevents charging.
  5. Transfer the starter clutch cleanly: BDK rotor to the starter clutch with thread-lock, nothing forgotten, nothing cross-threaded. And: never run the engine with the battery disconnected or the regulator unplugged.

Contents

1Before you begin – requirements & safety
2Check kit contents & ordered option
3Tools, materials, torque settings
4Removing the OEM generator
5Fit the rotor with the starter clutch
6Fit the new generator cover
7Mounting and connecting the racing regulator
8Commissioning & sign-off checklist
9Operation on the race track
10Fault finding with the multimeter
11Legal notes, warranty, contact

1Before you begin – requirements & safety

A BDK race generator kit replaces the rotor (flywheel), stator (coil) and regulator/rectifier with a significantly lighter unit designed for race use. The lightweight rotor saves a large part of the rotating mass of the original generator – you feel it when tipping into corners, when downshifting and in throttle response. The price: the system demands a careful installation and changed operating behaviour (Section 9).

What you should be confident doing

  • Removing the fairing, generator cover and flywheel with a puller – without force and without damaging gasket faces; separating the flywheel and starter clutch
  • Working with thread-locking compound and a torque wrench in the 5–35 Nm range
  • Clean the sealing faces properly, fit the new paper gasket and locating dowels correctly
  • Vehicle wiring: identifying a switched live, tapping into it cleanly and insulating it; checking connectors
  • Measuring with the multimeter in AC, DC and Ω (continuity)

If you are unsure about any point

Have the installation carried out by a specialist workshop or an experienced race mechanic. A mistake here can cost the rotor, stator, regulator or, in the worst case, the engine. If you have technical questions about the kit, we are happy to help before installation – contact details are on the last page.

These instructions are deliberately detailed. Experienced mechanics can skim the basics; the points in bold and the test values apply to everyone.

Safety while working
  • Let the engine cool down completely. Support the motorcycle securely (rear paddock stand, front stand if necessary), ignition off, remove the key.
  • Disconnect the battery first – always undo the negative terminal first and connect it last when reconnecting. With lithium batteries, never lay tools across both terminals.
  • The generator cover is oil-wetted. Drain the engine oil before opening (Step 1) – this way only residual oil runs out when the cover is removed, the gasket faces stay dry and the bearing area stays clean. Have a drain pan, rags and gloves ready; remove any oil on tyres or brakes immediately.
  • The rotor is a permanent magnet: swarf, screws and metal debris are attracted to it. Before fitting, dab the magnet side thoroughly with adhesive tape and check it.
  • Use thread-locking compound, silicone remover and sealant only in ventilated rooms; observe the safety data sheets.

2Check kit contents & ordered option

Check the contents completely before you strip the motorcycle. If anything is missing or a part is damaged, do not start the installation – contact us.

ItemQty
Complete generator cover with ready-fitted racing stator windings assembly and pre-assembled stator connector1
Rotor assembly (lightweight rotor, bolted to the original starter clutch)1
Racing regulator/rectifier with connecting leads, green LED, fuse holder (30/35 A) and adjustment screw1
Aluminium washer for the rotor bolt1
Thread-locking compound, small bottle1
Original fitting instructions BDK Race Engineering (“R6 to 2005 Race Generator Fitting Info”, English)1
Kit contents R6
Example photo (kit R6 2006+, photo BDK): complete cover with stator and connector, rotor – the 03–05 kit is built the same way.

Your ordered option (please tick)

Comfort Relayyes – nothing needs to be disconnected after use
no – battery or regulator is disconnected after use
ConnectionRing terminals directly to the battery (there is no OEM-connector conversion for Yamaha)
What the kit does not include

New cover gasket (genuine Yamaha part – according to BDK a gasket is mandatory, no sealant), flywheel puller to suit the R6, engine oil with sealing washer for the drain plug and the recommended LiFePO4 battery (min. 7.8 Ah, better 10.4 Ah). A battery isolator switch makes sense if you have not ordered a Comfort Relay (Section 9).

The complete installation manual (11 pages) is included in print with every kit.

0 of 0 reviews

Average rating of 0 out of 5 stars

Leave a review!

Share your experiences with other customers.


Skip product gallery

ZUBEHÖR & ERSATZTEILE RACING LIMA´s

REPLACEMENT STATOR Racing ALTERNATOR
REPLACEMENT STATOR Racing ALTERNATOR

Replacement Coil Racing Alternator is the BDK alternator coil (stator) as a spare part for all BDK racing alternator kits: identical to the coil supplied in the kit, available either pre-fitted into the carrier ring or as a single coil – for replacement after a defect, crash or heat damage. Type Stator Stator, identical to the kit stator Version select­able with or without carrier ring Fits uni­ver­sal Carrier ring is model-specific Part number RG-SPP-SPULE Spare part: STATOR for racing alternator kit Suitable for skilled hands who can carry out the installation and wiring themselves or including stator mounting ring, with the stator fitted by us. For DIY buyers: The damaged stator unit can be removed by pushing it out. Take note of where the stator wires must end in relation to the mounting holes of the retaining ring. Heat the ring holder, e.g. on a hotplate - the stator unit should then drop out. Make sure that the wires do not touch the hot retaining ring and that the stator unit is seated flat and flush, fully inside the retaining ring. Only the stator core should be visible above the edge of the retaining ring. Once the sheathing has cooled down, the connectors can be reused with new wire ends to be crimped. Please note that some early alternator kit models contained a slightly different stator unit. In this case, please order with the mounting ring.

Regular price: From €329.00
REPLACEMENT REGULATOR Racing ALTERNATOR
REPLACEMENT REGULATOR Racing ALTERNATOR

Replacement Regulator for Racing Alternator is the intelligent 3-phase 240 W regulator/rectifier for all BDK racing alternators: rather than regulating by short-circuiting like conventional regulators, it regulates according to load, resulting in significantly less heat build-up and no heat-related failures on the racetrack – ideal as a replacement or spare for your racing electronics. Type Reg­u­lator 3-phase regulator/rectifier Output 240 W load-dependent, low heat generation Comfort relay select­able with or without comfort relay Fits all BDK racing alternator kits Part number RG-SPP-REGREC Spare Part: Regulator for Racing Alternator 3 Phase Regulator/Rectifier. Every year a high number of alternators fail due to lack of heat transfer and cooling. One reason for this is imbedded in the design of many Japanese and aftermarket regulators. They work by short circuiting the generator, and by doing so the regulator is running at 100% capacity all the time. This way the excess power produced at high rpm by the generator is transferred from electrical energy to heat in the alternator and the regulator. Our regulators work by disconnecting the alternator from the regulator when there is sufficient voltage in the battery. Because the alternator is running without any load it produces less heat and resistance. This design lengthens the life of both the alternator and the regulator, and less resistance on the engine (= more power). The ultimate output of the regulator voltage is adjustable and this product is suitable for use with all types of Lithium racing batteries. There is an LED fitted to the regulator which shows when the regulator is overcoming load on the system. This will work with ALL types of 3 phase alternators and generators. The 3 phase Regulator/Rectifier MUST run with a battery at ALL times. Connection: The regulator is connected to the alternator by the 3 wires in no particular order. The red wire is connected to the battery +ve, via a fuse (fitted). The black wire is connected to the battery –ve. The housing of the rectifier has to be earthed with fitting directly to the body or with an extra wire. The thin blue wire is connected to a switched +ve 12V supply (so no drain occurs when the vehicle is off). You cannot test or run the regulator without the battery connected. The battery and alternator must be charged and in good working order. Always ensure the battery is fully charged before starting. When mounting the regulator please ensure there is good airflow and as much space as possible around it. Spacers behind the regulator will allow extra airflow behind it.

Regular price: From €275.00
RACEPACE LiFePO4 Endurance Power
RACEPACE LiFePO4 Endurance Power

RACEPACE LiFePO4 Endurance Power is the LiFePO4 motorcycle battery for racing: up to 75% lighter than conventional batteries, with active cell balancing, an external balancer connector and polyimide-insulated 26650 cells – handmade in Germany. Type LiFePO4 bat­tery Racing, handmade in Germany Balancing active with external balancer connector Cells 26650 polyimide-insulated Recommended for motorcycles with a racing alternator (at least 7.5 Ah, ideally 10 Ah). Article number LIFE_BATT You are ordering a RACEPACE LiFePO4 Endurance Power battery – a high-performance battery system consistently engineered for racing applications. The focus is on electrical stability, repeatable power delivery and maximum reliability under heat, vibration and high current peaks. Nominal voltage13.2 VLiFePO4 · 26650 cylindrical cells Capacity5.2 – 15.6 Ahfive sizes · 8 to 24 cells Weightfrom 0.75 kgup to 75% lighter than conventional motorcycle batteries Continuous dischargeup to 312 Apulse (10 s) up to 720 A 1Technology in detail Polyimide-insulated individual cellsEvery 26650 cylindrical cell receives a high-temperature-resistant, electrically stable polyimide sleeve. Unlike PVC, the insulation remains virtually unchanged over a very wide temperature range and the entire service life – even under vibration and in a tightly packed cell pack. Copper busbars and spot weldingLow-resistance copper busbars, welded with a transistor-controlled bipolar spot welder. Pneumatically regulated electrode pressure ensures reproducible weld quality with minimal thermal stress on the cells. Active cell balancingThe integrated active balancer continuously monitors all cell voltages, intervenes from a difference of 0.1 V – even during charging – and balances the cells down to 0.01 V. External balancing portA dedicated connector allows targeted fine balancing with a smart charger, independent of the onboard charging system. High-temperature and impact-resistant enclosureHigh-performance engineering polymer with high temperature resistance, excellent impact strength and lasting dimensional stability – protection against mechanical and thermal stress in racing. Manufactory quality – Made in GermanyEvery battery pack is assembled and tested by hand: not a mass-produced product, but a deliberately over-engineered high-performance energy system. Fine balancing once per race weekend TipVia the external balancing port, a smart charger additionally fine-balances the cells. This keeps the cell pack stable and the full capacity usable. 2Technical data Parameter5.2 Ah7.8 Ah10.4 Ah13.0 Ah15.6 Ah Nominal voltage13.2 V Number of cells812162024 Capacity at 23 °C5.2 Ah7.8 Ah10.4 Ah13.0 Ah15.6 Ah Max. continuous discharge104 A156 A208 A260 A312 A Max. discharge pulse 10 s240 A360 A480 A600 A720 A Length × height110 × 79 mm Width56 mm83 mm110 mm137 mm164 mm Weight0.75 kg1.10 kg1.40 kg1.75 kg2.10 kg 3Charging and operation Important: never exceed a charge cut-off voltage of 14.4 VUse only LiFePO4-compatible chargers with CC/CV characteristics (“LiFe” programme). 14.4 V corresponds to 3.60 V per cell – higher values overcharge the cells and shorten their service life. No lead-acid chargers, no desulphation or pulse programmes. Parameter5.2 Ah7.8 Ah10.4 Ah13.0 Ah15.6 Ah Recommended charge current5 A8 A10 A10 A10 A Max. continuous charge current52 A78 A104 A130 A156 A Charge cut-off voltage14.4 V Float charge voltage14.0 V Temperature ranges Discharging-30°C to 60°C Charging ambient temperature0°C to 60°C Storage-40°C to 70°C The cells can be charged at an ambient temperature of 0 °C to 60 °C. In its preset LiFe programme, the HTRC T150 charger only charges between 0 °C and 45 °C. 4Technology and advantages TechnologyFeaturesAdvantages Polyimide cell insulationFeaturesAdditional insulation on every individual cellHigh dielectric strengthElectrically stable at elevated temperaturesMechanically stable under vibrationAdvantagesLong-term stable electrical insulationReduced risk of leakage currentsIncreased operational safetyConsistent racing performance Active cell balancingFeaturesActive from 0.1 V voltage differenceBalancing during chargingBalances down to approx. 0.01 VEnergy-efficient with minimal heat generationAdvantagesMaximum usable capacityUniform cell agingSignificantly extended service lifeStable long-term performance External balancing portFeaturesDedicated connector for smart chargersTargeted fine balancing possibleIndependent of onboard charging systemAdvantagesPreventive stabilization of the cell packRecommended for racing useFull control instead of a black-box battery Copper busbars & spot weldingFeaturesLow-resistance copper busbarsTransistor-controlled bipolar weldingPneumatically regulated electrode pressureMinimal thermal stress on cellsAdvantagesExtremely low contact resistanceHigh cranking current capabilityReproducible manufacturing qualityMaximum electrical efficiency High-performance enclosureFeaturesHigh-temperature resistant engineering polymerHigh impact resistanceDimensional stability under continuous loadAdvantagesProtection against heat & vibrationHigh mechanical safetyDesigned for racing environments 5Performance data ParameterValueDescription Usable capacityValue94.2 %Descriptionat 1C discharge (10.4Ah version) Capacity after 1000 cyclesValue86 %Descriptionat 1.2C charging (25°C) Weight reductionValueup to 75%Descriptioncompared to conventional motorcycle batteries Discharge temperature rangeValue-30°C to 60°CDescriptionExtreme temperature range for all applications 6Safety and test standards Important safety information Water protection: Do not immerse the battery in water or expose it to moisture. Fire protection: Do not throw into open fire or expose to extreme heat. Mechanical: Do not open, puncture, or mechanically damage the battery. Electrical: Avoid short circuits and reverse polarity at all costs. Charger: Use only chargers suitable for LiFePO4 with CC/CV characteristics. Safety testResultStandard Nail penetrationPassedEUCAR 4 Deep dischargePassedEUCAR 3 Thermal stabilityPassedEUCAR 4 External short circuitPassedEUCAR 3 Crush testPassedEUCAR 3 OverchargePassedEUCAR 2 Quality standards: UN 3480 (UN 38.3), UL 1642, UL 1973, IEC 62133-2, REACH, RoHS, ISO 14001, IATF 16949, ISO 9001. 7Optional accessories 75A battery terminal instead of standard ring terminals matching 75A onboard connection adapter matching 40A onboard charging adapter 40A charging cable for compatible smart chargers

Regular price: From €199.00
Replacement COIL ADAPTER PLATE Racing Alternator
Replacement COIL ADAPTER PLATE Racing Alternator

Replacement Adapter Plate Racing Alternator Coil is the BDK mounting plate on which the racing alternator coil is fitted inside the alternator cover: CNC-machined, compatible with the BDK coils of the BP01–10 series – as a replacement after damage or for a second cover. Type Plate Stator adapter plate, CNC-machined Series BP01–10 BDK stators Scope of delivery 1 plate without stator and bolts Fits BDK racing alternator kits with stator adapter plate BP01–10 Part number RG-SPP-ROT-BDK_BP01-10 Replacement COIL ADAPTER PLATE Racing Alternator 1Application Mounting plate on which the racing alternator stator is secured in the alternator cover Replacement after damage or for a second cover 2Scope of delivery 1 adapter plate without stator and screws Suitable for BDK stators of the BP01–10 series.

Regular price: €145.00
Puller 2-piece for Racing Alternator Rotor
Puller 2-piece for Racing Alternator Rotor

2-Piece Puller for Racing Alternator Rotor is the two-part BDK tool for removing the rotor from all BDK Racing alternators: the outer puller engages on the rotor, and the central puller bolt pushes the rotor off the crankshaft in a controlled manner – for maintenance, coil replacement and engine conversion. Type Rotor puller 2-piece, for BDK rotors Scope of delivery 2 pieces External puller, puller bolt Fits uni­ver­sal all BDK rotors Part number RG-BDK-ABZ-2TLG Two-piece flywheel puller for racing alternator magnet rotor When removing rotors with the two-piece puller: First, carefully remove the aluminium threaded disc (with nut head). On newer versions, removing the nut/threaded disc is not necessary, as there is sufficient thread available. Allow the outer puller to engage fully. Tighten the central puller bolt until the rotor is released. On some models, it may be necessary to loosen the bolt that secures the rotor so that the puller can press against it to release it.

Regular price: €59.00
Battery Isolator Switch 12 - 32 V 3 Positions
Battery Isolator Switch 12 - 32 V 3 Positions

Battery Isolator Switch 12–32 V, 3 Position is the main switch for safely disconnecting the battery from the electrical system, recommended for all motorcycles fitted with a racing alternator: protects the (LiFePO4) battery from deep discharge during storage periods, three detent positions, removable rotary knob in the Off position, up to 100 A – for racing motorcycles. Type Master switch Battery isolator switch, 3 detent positions Current rating up to 100 A 12–32 V Mounting Ø 29 mm removable rotary knob Suitable for all 12 to 32 V electrical systems, installation diameter 29 mm. Item number RG-ACC-BATTSWITCH-3-POS Battery Disconnect Switch 12 - 32 V 3 positions Recommended for all motorcycles with racing alternator. Comfortable and secure battery disconnection. protect the battery when bike is not in use from discharge. Switch has 3 setting position, removeable in Off-Setting. Needed whole cut for installation 29mm12-32V100A max.

Regular price: €22.90
DIRKO HT BLACK Sealant ProfiPress 200ml 471.501
DIRKO HT BLACK Sealant ProfiPress 200ml 471.501

DIRKO HT Black Sealant ProfiPress 200 ml is the high-temperature-resistant silicone sealant from Elring (471.501) in the ProfiPress cartridge: permanently elastic up to 250 °C, resistant to oil and coolant – for sealing the alternator cover when fitting the BDK racing alternator and for all engine casing sealing surfaces without a paper gasket. Type Seal­ant Silicone, Elring 471.501 Temperature up to 250 °C permanently flexible, resistant to oil and coolant Contents 200 ml ProfiPress cartridge Suitable for all alternator and engine covers; recommended for every BDK racing alternator installation. Part number RG-Acc-DirkoHT Sealing compound DIRKO HT BLACK ProfiPress 200ml 471.501 Very easy to dose and a perfect consistency. Resealable. Suitable for Don't buy anything cheap. Should always be with you. Nnow based on oxime (neutral cross-linked) - silicone Temperature range from -60°C to + 285 °C (on 24h to + 315°C) pasty, stable, permanently elastic when cross-linked not solvent based UV-resistant non-flammable pressure packaging with new closure technology (handy clip closure and 90° locking nozzle) Color: Black Content: 200ml max. sealing gap: 2.0mm electrically insulating no drying out MEKO-free Reliably seals surfaces, crevices and cracks even when moving. Can be used as a seal for aggregates, engine housings, gears, end caps, oil pans and various engine parts. Neutral cross-linked, also suitable for light alloy engines. Resistant to ozone, extreme weather conditions, cold and hot water, salt water, fats and mineral oils.

Regular price: €17.90
Voltmeter Display DC 8-16V
Voltmeter Display DC 8-16V

Voltmeter display DC 8–16 V is the compact digital voltage display for the 12 V electrical system: it shows the racing alternator's charging voltage and the battery condition directly on the cockpit, so that regulator or battery issues can be detected early on the track. Type Volt­meter digital cockpit display Display range 8–16 V 12 V electrical system Included in delivery 1 dis­play with connection cable Suitable for all 12 V electrical systems (display range 8–16 V), recommended in combination with a BDK racing alternator and LiFePO4 battery. Item number RG-ACC-VOLT-DISPLAY Voltmeter Display DC 8-16V 1Specifications Display mode: LED digital Display color: Green Measurement Range: DC 8V - 16V Measurement accuracy: ±(0.2%) Dimension: 5.7 x 2.9 x 1cm / 2.2" x 1.1" x 0.4" Wire length: 90cm / 35.4" Waterproof, Dustproof, Shockproof. Simple connection, easy to use. Mini size with 3-digit LED Digital Display. Measures DC Voltage precisely from 8V to 16.0V. Widely used for cars, motorcycles, bikes, substation automation, distribution automation, test equipment, voltage regulator and so on. Displays "LLL" when the voltage is lower than measuring range; displays "HHH" when the voltage is higher than the measuring range. Installation: red to switsched 12V source black to mass red to switsched 12V source black to mass

Regular price: €14.90
1m charging cable XT60 to 4mm banana plug AWG12
1m charging cable XT60 to 4mm banana plug AWG12

1 m XT60 to 4 mm Banana Plug Charging Cable connects LiFePO4 batteries with an XT60 connector to the HTRC T150 charger – with flexible AWG 12 silicone cables. Type Char­ging cable XT60 to 4 mm banana plug Length 1 m AWG 12, silicone Suitable for HTRC T150 and batteries with XT60 connector Article number LFP-LZM-LK1M 1m charging cable XT60 with 4mm banana plug with AWG 12 silicone wires suitable for LiFePo4 battery and HTRC 150 charger

Regular price: €14.90